I have the Pro version and had the same issue, and was a little perplexed why they made it where tx would not fit the case with the mount on it. But then I realized it will fit if you turn it face down. Seems to fit fine that way. Not sure if the Auto version is different enough that it would not fit if turned face down, it may not.
Hi peters, Not sure of the reception as I have had some issues with the range of my fpv transmission and been flying line of sight so max I've been is about 260 metres at the moment. I done it more to enable me to easily dismantle and store in the case when finished.
The only thing that I need to do is to tap a bolt to stop the arm from dropping down with the weight of the monitor, but I use it with a lanyard which attaches to the arm so its not to bad at the moment. Normally it has a little bolt to stop it from dropping down but as I've had to turn the mount around I cannot use that hole as it would touch the controller (this way nothing covers the osd on the controller).
I got it from ebay, just search for fpv mount and you should find them. Link below to show you what you need, this is located in the uk so search for one nearer your location. Make sure you get the one which mounts horizontal and not vertical as there are 2 different types.
Thanks for the link,I will get one of those for sure. I am also going to get a prop ballancer, I don't know how much good it will do, but 2 brand new unused carbon fibre props were 17.37 grams and 17.59 grams, makes me curious about ballance.
hi i just made a bracket similar to the one shown. i made it out of a piece of 3mm x 20mm wide stainless steel filled and tapped one end to take 5mm screw and put a bend 25mm up from the bracket then added 100mm in length put a bend back and drilled a 7mm hole to take the mounting of the screen i will put up a couple of photos tomorrow simple to make and costs nothing only a bit of time and works a treat
Welcome to Shoutbox! Our quick and easy way to chat with each other!
vladko: Is it possible to change the remote control of Splash Drone with Splash Drone 3? What are the requirements if this is possible?
Jul 3, 2020 22:55:58 GMT
chris: I had to go through all the settings in the app (computer) and reset some settings as well as reset some of the defaults. After that I was good to go again.
May 8, 2020 22:32:57 GMT
chris: marksdrone: just had the same issue with mine. It may be the accelorometer that you need to calibrate first and then do the compass after that.
May 8, 2020 22:31:44 GMT
marksdrone: Hi everyone.. i just got a older splash..auto .2017 model..it wont calibrate. Goes through the motions . Untill i get that single blink. When i pull down to activate motors the single blink turns solid.and nothing happens . please help..
May 7, 2020 17:15:21 GMT
chris: Can't wait to get the old bird back up in the air and test tomorrow!!
May 2, 2020 3:10:52 GMT
chris: I then got the "green paper airplane" once again.
May 2, 2020 3:10:16 GMT
chris: I had to pair UAV-1 (receiver) to my phone then I could open the app and connect to UAV-2(transmitter)
May 2, 2020 3:09:42 GMT
chris: Also I didi have to play around with the bluetooth on my phone with transmitter and receiver.
May 2, 2020 3:08:55 GMT
chris: Had a hell of a time with the compass. Also make sure the last page it is on COM not RC.
May 2, 2020 3:08:28 GMT
chris: Got my old school app to work! Messed around a bit in the swellpro computer program and made sure all settings were recognized.
May 2, 2020 3:07:53 GMT
chris: I have an original Auto from WAY back. I cannot get it connected to the app and I was going to try the new app to see if it would work but it won't even stay open on my phone.
Apr 30, 2020 19:58:09 GMT
seanprokopec: Does anyone have an idea how to troubleshoot connecting to the swellpro fly app on an adroid device. I have a Splashdrone Auto Plus. The app seems to be working fine, it just won't connect...
Apr 22, 2020 14:41:02 GMT
rescorpione: also try to take a look at the discussion Faults & solutions
Apr 11, 2020 9:14:05 GMT
rescorpione: Hi Coz I had the same problem with splashdrone 3+ I solved it by updating the app,I contacted support because the one on the play store was the old version,however try to update swellpro spry app
Apr 11, 2020 9:12:47 GMT
coz: i am having a problem with the Spry+ app showing current gps terrain. I have a blank screen. Any ideas?
Apr 10, 2020 19:35:39 GMT
rescorpione: Hi guys how are you, I'm Alessio and I live in Milan Italy,unfortunately at the moment I am living an unpleasant reality because of the covid-19,however I wanted to share with you my new purchase the splash drone 3 plus with PL3....Hello everybody
Mar 12, 2020 20:23:14 GMT
roberts: I need help with wiring diagram or photo of the flight controller. I have two wires from com 1 that have the pins slipped out of the plug to the main board. where can I find diagram or photos of this plug to the main board
Jan 18, 2020 20:46:36 GMT
amhulli: Hi, new to the splashdrone and can't get either of my two iPhones to pair with the bluetooth datalink. Will pair with my son's Android phone. Anyone else experience this?
Dec 29, 2019 2:00:23 GMT
so54i88: darkdimension, I have the same "please switch to mode p" message. Have you figured out it means?
Dec 16, 2019 1:59:49 GMT