I've been looking at a set like them on ebay from china, which are very cost effective for me in the UK.
Have you noticed how the props supplied with the drone do not have the correct tolerance I would like to see from a nut and bolt, on mine as you screw them on there is far to much play between the motor shaft and prop.
If you get any, do a review on them and post it up!!
Nice to have a 3D printer.. I have just ordered some 8mm bushes to modify and try and straighten up the props when they are installed. Nice to know it will work and hopefully ensure the props are correctly balanced at all times.
The du-bro balancer is good and I would highly recommend it. The thread size is 6mm, you can look for the dji balancer as that uses a 6mm prop balance shaft as the motor thread is the same.
One of the issues I had balancing mine was when you screw them on the balance shaft they can sit a little off, so I put tape on the shaft to build it out to 8mm which sits in the end of the prop and straightens it up. I only put a small amount of tape on the side I was balancing so it did not cause any in balance.
mod95: Hey any one out in our SD world have a Auto Plus flight controller? willing to let 1 go?
Feb 5, 2021 1:37:41 GMT
corsair40: j'ai un splash drone 3+je suis incapable de le met a jour, j'aimerais savoir comment,,,,,,,,,,,,,merci
Dec 15, 2020 18:41:59 GMT
ryzer: Disconnected the flight controller , anyone got pictures of connectors at both ends?
Nov 23, 2020 12:15:01 GMT
tyuyrt: Hello, I just installed a new GPS with lid - it only works when the lid and cable are dangling down the side of the drone; as soon as I close the lid the lights flash yellow red and green and I cannot take off. I'd appreciate any insights.
Oct 22, 2020 21:49:32 GMT
robertinmaine: I have a Splash Drone 3 with an intermittent issue with recording/pictures. After several attempts to fix over emails, Sent drone and controller to Urban Drones, fixed, said it was a pairing issue. Worked for 1 flight Records when on WIFI. Suggestion?
Aug 18, 2020 13:32:32 GMT
vladko: Is it possible to change the remote control of Splash Drone with Splash Drone 3? What are the requirements if this is possible?
Jul 3, 2020 22:55:58 GMT
chris: I had to go through all the settings in the app (computer) and reset some settings as well as reset some of the defaults. After that I was good to go again.
May 8, 2020 22:32:57 GMT
chris: marksdrone: just had the same issue with mine. It may be the accelorometer that you need to calibrate first and then do the compass after that.
May 8, 2020 22:31:44 GMT
marksdrone: Hi everyone.. i just got a older splash..auto .2017 model..it wont calibrate. Goes through the motions . Untill i get that single blink. When i pull down to activate motors the single blink turns solid.and nothing happens . please help..
May 7, 2020 17:15:21 GMT
chris: Can't wait to get the old bird back up in the air and test tomorrow!!
May 2, 2020 3:10:52 GMT
chris: I then got the "green paper airplane" once again.
May 2, 2020 3:10:16 GMT
chris: I had to pair UAV-1 (receiver) to my phone then I could open the app and connect to UAV-2(transmitter)
May 2, 2020 3:09:42 GMT
chris: Also I didi have to play around with the bluetooth on my phone with transmitter and receiver.
May 2, 2020 3:08:55 GMT
chris: Had a hell of a time with the compass. Also make sure the last page it is on COM not RC.
May 2, 2020 3:08:28 GMT
chris: Got my old school app to work! Messed around a bit in the swellpro computer program and made sure all settings were recognized.
May 2, 2020 3:07:53 GMT
chris: I have an original Auto from WAY back. I cannot get it connected to the app and I was going to try the new app to see if it would work but it won't even stay open on my phone.
Apr 30, 2020 19:58:09 GMT